How to hook up your subs for powerful bass
by Crutchfield's Buck Pomerantz
Aug 31, 2023
In this article, we'll help you find the best way to connect your subs to your amp. We begin with some basic – and important – subwoofer and amplifier terms. But if you want, you can skip straight to the wiring diagrams.
[Ve este artículo en español]
There are many ways to wire subwoofers and amplifiers together. The ideal setup is when subs and amps match their impedance and power capabilities to optimize performance.
Power with care
The diagrams show wiring configurations for amplifiers and subwoofers that have already been matched for power capabilities. You should never connect subs to an amp that could give them more power than their total watts RMS power ratings. Doing so could damage the subs or the amp. See How to match subs and amps for further guidance.
Here's an example diagram for connecting two 4-ohm DVC subs to a mono-channel amplifier:
Wiring terms you need to know
The diagrams are below, but first let's explain a few important terms.
SVC
A single voice coil sub with two wiring terminal posts, one marked positive and the other marked negative.
DVC
A dual voice coil sub with four wiring terminal posts, two positive terminals and two negative terminals. This gives you more options for wiring the sub in different situations.
Ohms
The impedance load, or resistance against the amplifier's output signal, of a subwoofer coil. Subwoofer voice coils usually come in 2-ohm, 4-ohm, or 8-ohm impedances. The value is often found printed on the magnet, if you're unsure of what you have.
Series wiring and parallel wiring
These terms refer to two ways of routing the speaker wires to properly manage the overall impedance load. Whether you need to use a series wiring configuration, parallel wiring, or a mix of both, our diagrams will show you exactly the best way to wire your speakers, without using confusing technical terms.
When you wire dual voice coils and multiple subs together, the resulting total impedance is not always simple to figure out or practical to use. In the example diagram above, the voice coils of each sub are wired together in series, while the two subs themselves are wired together in parallel.
Amplifier output
An amplifier will put out more power through a low-impedance sub than it will through a high-impedance sub. But a lower impedance also means more stress on the amp. Some amplifiers (marked “low-imp” in the links below) can even drive a 1-ohm load safely, and achieve maximum output. Refer to your amp manufacturer or owner's manual to determine whether or not yours can handle a low-impedance load.
Bridged mode
Bridging an amp combines two amplifier channels into one, to get more power. The disadvantage of bridging is that bridged channels can't drive impedance loads as low as they can when unbridged. The proper way to bridge the amp is usually indicated at the amp's speaker wire terminals. For more information, read our How to bridge an amplifier article.
[Shop for car amplifiers]
Wire
All the wires depicted in the Subwoofer Wiring Diagrams are speaker wires. For wiring subwoofers, we recommend using wires of 12- to 16-gauge in size.
[Shop for speaker wire]
Find the right wiring diagram
Now, let's get those subs hooked up! All of our wiring diagrams are listed below. Select the diagram for the number and type of subs you have. Depending on your gear, there might be more than one way to safely wire the subs.
- 2 SVC 2-ohm subs, 2ch amp: 2 x 2 ohms
- 2 SVC 4-ohm subs, 2ch amp: 2 x 4 ohms
- 2 SVC 4-ohm subs, 2ch low-imp amp: 2 ohms
- 2 SVC 8-ohm subs, 2ch amp: 4 ohms
- 2 DVC 2-ohm subs, 2ch amp: 2 x 4 ohms
- 2 DVC 2-ohm subs, 2ch low-imp amp: 2 ohms
- 2 DVC 4-ohm subs, 2ch amp: 2 x 2 ohms
- 2 DVC 4-ohm subs, bridged 2ch amp: 4 ohms
A note about multi-channel amplifiers
5-channel amplifiers are a popular way to get "full system" power in one box — four channels to drive your four speakers, plus a fifth, higher-powered channel for your subwoofer. 6- and 8-channel amps are similar and offer even more flexibility. When it comes to connecting subwoofers to these amps, keep it simple:
- If you're connecting your sub(s) to the subwoofer channel, treat it like a mono-channel amplifier.
- If you're bridging two channels of your amp, simply treat it as a bridged 2-channel amp.
Start building your bass system today
Now that you've seen how to wire subwoofers and amplifiers together, you can knowledgeably shop Crutchfield's extensive selection of subwoofers and amplifiers. We also carry amp wiring kits, speaker wire, RCA cables, capacitors, and much more.
Contact us by phone, chat, or email and an Advisor will help you get what you need. If you want to learn more about amplifier systems, check out our Amplifier Installation Guide.
Comments (1,238)
-
Andreas from Los Angeles
Posted on 1/1/2024
Hello and I have 2 dvc 4ohm kicker comp vx at 750 rms each hooked up in parallel to a kicker 1800.1 amp with a 2ohm minimum impedance. Each subwoofer has a 2 ohm load because they are wired in parallel so it's a 4ohm load that my amp is taking do you think this is the best set up for my subwoofers and amp? I know my amp has 300watts extra power but how many watts are my subwoofers really taking and will they get ruined? Thank you!
Buck Pomerantz from Crutchfield
on 1/2/2024
Andreas, Don't be confused by "parallel" and "series" wiring terminology, but two DVC 4-ohm subs can get wired together to form a one-ohm load, a 4-ohm load, or a 16-ohm load. The only safe way to wire those subs to that amp is using the 4-ohm wiring option.
-
MARK TREVINO
Posted on 12/28/2023
I HAVE TWO DUAL COIL 8 INCH 4OHM KICKER SUBWOOFERS WITH KICKER AMP CXA400.1. WHAT IS THE BEST WAY TO GET THE MOST OUT OF THE AMP'S POWER INTO THE SUBS?
Buck Pomerantz from Crutchfield
on 12/29/2023
Mark, Without knowing precisely what the RMS power ratings of the subs you're referring to, we can't help you with wiring advice. If you want a question answered about a system, you must identify the gear by brand names and model numbers so we can get the right information to you.
-
C from Louisville
Posted on 12/23/2023
Can you run 4 d2 and link 2 1 ohm amps, but the 4 subs run at 1ohm??
Buck Pomerantz from Crutchfield
on 12/26/2023
C, You should absolutely never link two amplifiers together, unless they were designed to do so. Without knowing precisely what amps and subs you're referring to, we can't help you with wiring advice. If you want a question answered about a system, you must identify the gear by brand names and model numbers so we can get the right information to you.
-
Cameron
Posted on 11/20/2023
Can you wire a DVC and a SVC into a mono amp? If so how would you do it?
Buck Pomerantz from Crutchfield
on 11/21/2023
Cameron, If the power ratings are compatible, you can wire the two voice coils of a DVC 2-ohm sub together in series to create a 4-ohm sub that can get wired with a SVC 4-oh sub. Likewise, a DVC 4-ohm sub with its coils wired in parallel to create a 2-ohm sub can get wired with a SVC 2-ohm sub. Without knowing the specific make and models of the subs, it would be irresponsible to show wiring schemes that could result in damage.
-
PAUL from Spring Hill, Fl
Posted on 11/14/2023
So if I have 3 10s at 250 watts max..125 minimum at 4 ohms..Is I series them over from - /+ 1 10 inch sub another 10 inch to -/+ to another 10 ich -/+.... useing the negative - of the first sub then to use the positive + of the last... what will be the ohm load and wattage need to supply the subs and what to use for a amp
Buck Pomerantz from Crutchfield
on 11/15/2023
Paul, Without knowing precisely what subs you're referring to, we can't help you with advice. Are they single or double voice coil? What's their RMS ratings? If you want a question answered about a system, you must identify the gear by brand names and model numbers so we can get the right information to you.
-
Collin Roan
Posted on 11/10/2023
My factory stereo I don't have a wiring diagram. How do I find our what colors I tap into.
Buck Pomerantz from Crutchfield
on 11/11/2023
Collin, Not knowing exactly what vehicle, or amplifier, or subwoofers you have make it impossible to give advice on how to wire them together. If you want a question answered about your system, you must identify your vehicle and your equipment by brand names and model numbers. Give us a call and talk to one of our Advisors. We can help you choose the right gear and give you the right advice on how to install it.
-
Crew
Posted on 11/6/2023
I already have a MOSCONI ONE 100.6 amplifier installed in to my car and was looking for a subwoofer to go with it, will my amplifier be to powerful for a Rockford Fosgate P2D4-12 subwoofer? And if not so what cable should I use?
Buck Pomerantz from Crutchfield
on 11/8/2023
Crew, That subwoofer should work well with that amplifier. If you're asking what speaker wire to use - use 16-, 14-, or 12-gauge speaker wire from the amp's bridged channels to the sub.
-
Dalton from Minneapolis
Posted on 10/27/2023
I am planning to install a JL Audio SB-GM-SLVCC4/12TW3 Stealthbox subwoofer. I bought an JL Audio XD1000/1v2 Amplifier for it. Would this be too powerful an amplifier to power this sub? Could I power this sub with this amplifier? Everything I'm seeing is pointing to it being too powerful, and it looks like I'll have to swap to the XD600/1v2 amp. Thank you
Buck Pomerantz from Crutchfield
on 10/28/2023
Dalton, Your XD1000 is a bit too strong and could damage that sub. The XD600 will be a safer application and should provide enough loud bass to make you happy.
-
Luciano from Orland
Posted on 10/27/2023
I connected a 2 ohm dvc sub parallel to get a 1 ohm load at the amp, i connected the + to + and the - to - but instead of connecting the amp to the + of one voice coil and the - of the other voice coil i connected the amp to the connectors of one voice coil - and + will that affect anything?
Buck Pomerantz from Crutchfield
on 10/28/2023
Luciano, That way of connecting ends up being electrically identical to the way pictured.
-
Deigo
Posted on 10/15/2023
I have one sub woofer, want to connect it to my car stereo, but I don't know what wire goes where, it has a blk- red wire,, a blue - blk- wire, & a blk- white wire, I only have blk- wire connected to my stereo where do I connect the blue the nlk wire toThe sub woofer is a tri- wiring speaker
Buck Pomerantz from Crutchfield
on 10/16/2023
Deigo, Without knowing precisely what vehicle and sub you're referring to, we can't help you with advice. If you want a question answered about a system, you must identify the gear by brand names and model numbers so we can get the right information to you.
The easiest way to shop car audio online
Find what Fits your vehicle
Remove
Checking fit...
Related products
Loading...
Adding...
C$219.95 each
Loading...
Adding...
C$269.99 each
Loading...
Adding...
C$349.99 each
Related articles & videos
See all
- Car subwoofer buying guide Our subwoofer shopping guide will help you determine which kind of subwoofer and bass system you need to get the sound you want. by Crutchfield's Bob B.
- How to match subwoofers and amplifiers This step-by-step guide will help you make sure that your amps and subs are evenly matched and work well together. We explain how to select one to go with the other. by Crutchfield's Buck P.
- Tuning your subs What does the gain control do anyway? How should you set the low-pass filter? This article describes how to tune your amplifier so that your subwoofer sounds just the way you want it to. by Crutchfield's Buck P.
- What are dual voice coil subwoofers? Dual voice coil subwoofers are a popular choice among car audio enthusiasts who want more flexibility in wiring their sound systems. by Crutchfield's Bob B.
- How to choose a subwoofer box Subwoofers in sealed boxes play "tight" bass, while ported boxes sound "boomy." Which type you need depends on the style of music you like and how you want it to sound. by Crutchfield's Buck P.
- Subwoofers FAQ Which subwoofer will sound the loudest? Or the deepest? Which hits harder: one 12" sub or two 10" subs? How much power do I need? These answers and more in our FAQ. by Crutchfield's Crutchfield Writing Team
- How to build a subwoofer box Helpful tips and step-by-step instructions for designing and building your own custom subwoofer box. We walk you through the math and the actual build in detail, so you'll know how to do it yourself. by Crutchfield's Robert F.
- Headlights dim when the music plays Here we discuss the most popular fixes for an underpowered electrical system: the big 3 upgrade, a capacitor, a high output alternator, and a second battery. by Crutchfield's Buck P.
- Subwoofer Installation Guide This article describes the steps involved in installing a subwoofer in your vehicle. by Crutchfield's Crutchfield Writing Team
Compare the sound
SpeakerCompare™
Patented Virtual Audio™ technology for auditioning speakers online
Recommended
You can change this setting any time by clicking 'Headphones' in the main menu.
SpeakerCompare™ is protected by patents and patent applications owned by Crutchfield Corporation.
SpeakerCompare™
Patented Virtual Audio™ technology
Audition speakers before you buy
SpeakerCompare simulates the sound of home and car speakers through your headphones. It lets you compare sonic characteristics between speakers so that you can make a more informed shopping decision.
SpeakerCompare™ is protected by patents and patent applications owned by Crutchfield Corporation.
SpeakerCompare™
What to listen for
Track notes
Artist
- analyzer
- log
- linear
- messages
We're here to help
For free personalized advice, call 1-888-291-8923. Our Advisors have listened to most of the speakers we carry, and can help you make the best choice for your system.
We'd love to know what you think
Select your headphones
Recommended
You can change this setting any time by clicking 'Headphones' in the main menu.
Select a track to start listening
Audition speakers before you buy
SpeakerCompare simulates the sound of home and car speakers through your headphones. It lets you compare sonic characteristics between speakers so that you can make a more informed shopping decision.
Why selecting your headphones is important
SpeakerCompare tailors your listening experience to the exact headphones you have, so that what you hear is comparable to auditioning speakers side-by-side in person. Knowing which model headphones you’re using lets us remove any sonic coloring from your experience.
Two different listening modes
In an actual listening room, you'd find that some speakers play louder than others when fed the same amount of power. In equal power mode, you'll hear these differences in loudness as they naturally occur between speakers.
In equal volume mode, we've made the loudness of each speaker about the same. This gives you a more direct comparison of subtle voicing differences between speakers.
Nothing beats listening to speakers in your space
SpeakerCompare gives you a sense of the sonic differences. But performance in the real world is affected by the acoustics of your car or home, your choice of amplification, and your source material. We still believe that the gold standard for auditioning speakers is hearing them in your own environment — that’s why we offer a 60-day money-back guarantee.
Our Listening Kit
To help you choose the right speakers, we recommend using Crutchfield’s SpeakerCompare Listening Kit. It includes a pair of studio-quality headphones, and a guide to getting the most out of your session, and a few other necessary items. We’ve carefully chosen the components of this kit to ensure a crystal-clear listening experience. It’s available for a nominal rental fee, and includes a $25 Crutchfield merchandise credit.
Request a kit
Rate your experience with SpeakerCompare
Thank you for your feedback!
We'd love to know what you think
